P0C73 Coolant Pump Error

Mitsubishi i-MiEV Forum

Help Support Mitsubishi i-MiEV Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Might want to review that wiring diagram for the coolant pump before getting too wild with applying power to signal control lines with no current regulation or fuse.

How will you measure the speed?

What will it mean if the pump seems to run? (but no speed measurement)

what if it doesn't run? (without knowing if the wiring or power sequence is correct)
 
Thanks kiev,
I did try applying power directly to the pump socket, unfortunately with nil result.
12v +ve to pin 3 Vbatt
12 -ve to pin 4 eth
12v =ve to pin 1 (wp) Vbatt
also measured voltages on plug
with key to Aux position
12v pin 3
with key to On position
14v pin 3
so appears as if Volts are at least getting to the pump plug ie relays and fuse ok.
also measured DC resistance of pump coil pin 3 to pin 1 930 ohms.

So my conclusion : Pump is "kaput" !

However philsuth was talking about testing his old pump in a bucket and it would be interesting to
know if he can power up his pump using the same method as I. (before I pull mine out).
How about it phil ?

Have looked at new pumps, some available from Japan and also from USofA (at a cost $$$$s)

Thought bubble .... 12v bilge pump as a temp measure ... hand operated ...... ha !

Bruce
 

Attachments

  • Coolant Pump Plug.JPG
    Coolant Pump Plug.JPG
    79.4 KB
  • Coolant Pump Control Unit-01.JPG
    Coolant Pump Control Unit-01.JPG
    42.6 KB
Another thought :
Here in Aus we have Mitsubshi PHEV (Plug In Hybrids) using the 10.5kw iMiev battery, I wonder how they keep the OBC cool when charging ?
Any PHEV experts out there ??
 

Attachments

  • PHEV Coolant pump-02.jpg
    PHEV Coolant pump-02.jpg
    37.8 KB
  • PHEV Coolant pump-01.jpg
    PHEV Coolant pump-01.jpg
    38.2 KB
It looks almost like the same pump is used on the PHEV ? Not that it helps lower the price.

From a few pictures on the phev forum it appears that they use the same looking OBC, but i haven't seen the insides of one yet to say for sure. But it is likely to be cooled in a similar manners--with a coolant flow to chill an internal heat sink plate.

With power and ground on the correct pins, then the speed might be controlled with a variable voltage on the WP terminal. [ref the control diagram above]


If you are up for more experiments--
Does any voltage appear at the WP terminal when the power and ground are applied? Maybe pulling WP down with a 1k resistor to ground would turn ON the pump? The FSM says to not run it without fluid, probably damage to internal seals.
 
Last edited:
Thankyou All,

I have left the pump on the car and ordered a new one, probably a month before it arrives, will resume the conversation then.
In the meantime I have learnt a 'lot' but probably just a 'little' about how the little car works ..... interesting exercise.

I must have upset the "pump GODS" my pool pump is making some strange noises ..... next task ....

An aside new pool pump <$400AUD delivered new cooling pump >$500AUD delivered

Happy days
regards
Bruce
 
OK, between travel to NZ, another round of COVID, and then all of the associated catching up from both sets of downtime, my iMIEV debugging has taken a back seat. However I spent a little time over the weekend and built up a test rig with a bucket of water (less messy than coolant to clean up if things go wrong) plumbed into a pump via clear vinyl tubing and driven by a bench supply. Once primed, the pump appears to work well . It draws about 5A in operation with a 13.8V supply.
I've established that the WP signal is not a voltage based speed control - the pump has only two states, running or not running. When WP is high, the pump runs, when it is low it stops. PWM on this signal could give speed control, but I've seen no indication that the iMIEV uses this capability so haven't tried it out. There's an internal pullup resistor on WP, so if the signal is not connected the pump just runs continually.
The WPN signal from the pump needs an external pullup resistor, and delivers the pulse stream I described before when the pump is turning. My bench pump (the original one from the car) delivers around 205Hz when the pump is running. The pump appears to take about 200-300ms to come up to full speed from start. This 205Hz is pretty close to the values seen from the other pump on the vehicle.

Also, during several runs to/from work I've seen the trouble light come on for the P0C73 code. I've never seen the pump run again after the light comes on, unless I either a/ shut the car right off, wait 2-3 seconds for the light to go out, then turn it on again (I've done this at red traffic lights), or b/ use a scan tool to reset the P0C73 code. I've also seen the P0C73 code come up during charging.

At this point I'm inclined to think my problem is in the ECU or nearby wiring, so will have a closer look this weekend.
 
Thanks for the feedback philsuth, interesting outcome, yours appears to be of a different nature to my fault, however as I have set out below I haven’t installed the new pump yet …..
and yes the P0C73 alarm does come up when charging .....

Status on my P0C73 Fault :

So that I could keep driving the MiniCab until the new water pump arrived from Japan I purchased a cheap pump off EBay as a interim and hooked it up to a 20 amp switch in the drivers cabin.
So each time I start the car I also switch on the pump, also switch it on when charging the MiniCab.

Obviously still get the P0C73 alarm, however fluid is continuously circulating so everything is staying cool.
A bit of a 'Heath Robinson' contraption , however it works satisfactorily.

The new pump arrived from Japan, it only took a couple of weeks instead of a couple of months as was stated on the initial order so I must commend the parts supplier .
https://www.ebay.com.au/itm/364694129657

As the interim pump was working so well and the weather here has cooled off (25C avg now) and I have been doing other things I have not as yet installed the new OEM pump.

I have however pulled the old pump apart (removed the rubberised gunk) down to the circuit board and when time is available will set up a ‘closed’ loop using some plastic pipe and bench test it and see if I can find the faulty component.

PS Also included a photo of how I removed the old pump and blocked off the fluid pipes using some clamps and wood ..... didn't loose any fluid ....

More to come in the near future : Bruce
 

Attachments

  • Interim Pump.JPG
    Interim Pump.JPG
    90.4 KB
  • Coolant Pump Circuit Board-01.JPG
    Coolant Pump Circuit Board-01.JPG
    95.1 KB
  • Coolant Pump Circuit Board-02.JPG
    Coolant Pump Circuit Board-02.JPG
    110.2 KB
  • Pump Removal.JPG
    Pump Removal.JPG
    88.5 KB
Last edited:
Hi,

Finally installed the new coolant pump, topped up the system and purged the air according to the instructions (attached).
1st of all I reset the DTCs P0C73 using the “Car Scanner” App

I mis-read Step 2. “Set the electric motor switch to “ON” position” and actually turned it to the “START” position (nothing happened the pump didn’t cycle), it actually means Set the switch to the “ACC” position.

Then within 7 seconds press the ASC-OFF switch (TCL switch in MiniCabs) more than 10 times.
Wait 20 seconds and the pump will start to cycle for 4 secs at a time each 30 seconds, during which time you need to top up as required.

After topping up I gave the car a road test for around half hour and no error messages, pump cycled on and off OK !

I am considering using the interim pump I purchased as a ‘Booster” pump and installing it in the pipe between the OBC and MCU with a manual switch, and turn it on when granny charging and/or when OBC temperature is at a particular level to provide additional cooling during our hotter weather.
 

Attachments

  • P0C73 Error.jpg
    P0C73 Error.jpg
    30.4 KB
  • Coolant Pump Error Proceedure.jpg
    Coolant Pump Error Proceedure.jpg
    27.7 KB
  • Coolant Pump Test Proceedure.jpg
    Coolant Pump Test Proceedure.jpg
    114.6 KB
  • New Coolant Pump Installed.JPG
    New Coolant Pump Installed.JPG
    84.7 KB
  • OBC to MCU cooling loop.JPG
    OBC to MCU cooling loop.JPG
    72.9 KB
I am considering using the interim pump I purchased as a ‘Booster” pump and installing it in the pipe between the OBC and MCU with a manual switch, and turn it on when granny charging and/or when OBC temperature is at a particular level to provide additional cooling during our hotter weather.
Well done on the repair and sharing your experience.

Not sure if adding a ‘Booster’ is going to make a significant difference , IIRC someone mentioned that the ‘cold’ transfer isn’t very effective to start with, pumping the coolant around faster will make little difference.

That said, it appears that installing a simple fan on top of the OBC is more effective.
 
Thanks MickeyS for the comment/feedback.

After reading many pages on the Forum regarding OBC failure it seems to me that heat has a large part to play in many of the fails, I used to work in an industry where we were told the Air-conditioning was not for our “comfort” it was there for the “comfort” of the equipment (to keep it cool) !

I have purchased an additional fan as per Michael8554 post, and will mount it in a similar manner.

https://myimiev.com/threads/supplemental-cooling-for-the-charger.4099/

I noticed that the air gap between the top of the OBC and the ‘floor’ cover is barely finger size and the heat build up there in summer is considerable, so some form of additional air circulation would be an advantage.

Its unfortunate that the Mitsu designers/engineers didn’t place all the electronics in a separate ‘sealed’ area away from road dirt and grime and allowed for forced cooling via fans, however it is what it is !

I have decided to follow some of the other contributors and only charge at the 6amp or 8amp rate maximum, I find that even though my MiniCab is a 2012 model the Main Battery still appears to be in reasonable condition and charges fairly evenly, just have to help out with keeping everything cool.
Cross fingers no more issues for a little while ……………. and thankyou for all contributions ............
bruce
 

Attachments

  • Battery Charged_105km_29-04-2024.jpg
    Battery Charged_105km_29-04-2024.jpg
    77.5 KB
  • Fully Charged_105km_29-04-2024.jpg
    Fully Charged_105km_29-04-2024.jpg
    43 KB
Have you (Bruce and philsuth) made any further progress on the coolant pump issue? I did some further testing and came up with results different from yours, philsuth. When the car is READY or during charging I measure (with a simple voltmeter, haven't tried an oscilloscope yet) the following:
-Between black (earth) and brown (feed from relay) line: 14.4V which should be normal (0V when off)
-Between black and green (WP) also 14.4 Volts (0V when car is off or not charging). I initially thought this was OK but following your readings I'm not so sure
-Between black and blue (WPN) always 0V. I would think this is the return line to the EV-ECU which measures the speed of the pump motor and triggers the yellow car exclamation when not according to specs.

I have not, as yet, done any DTC/OBD checks as I, as yet, am not equipped for this.

I removed the pump and the impeller turns freely so no issue of gunge or seized bearing.
Does anyone have any suggestion as to which further readings can be made because I'm thinking of simply replacing the pump with a used one from e-bay?
Has anyone ever tried to open the pump? It looks like it was not made to be repaired.
Thanks
Peter
 
Have you (Bruce and philsuth) made any further progress on the coolant pump issue? I did some further testing and came up with results different from yours, philsuth. When the car is READY or during charging I measure (with a simple voltmeter, haven't tried an oscilloscope yet) the following:
-Between black (earth) and brown (feed from relay) line: 14.4V which should be normal (0V when off)
-Between black and green (WP) also 14.4 Volts (0V when car is off or not charging). I initially thought this was OK but following your readings I'm not so sure
-Between black and blue (WPN) always 0V. I would think this is the return line to the EV-ECU which measures the speed of the pump motor and triggers the yellow car exclamation when not according to specs.

I have not, as yet, done any DTC/OBD checks as I, as yet, am not equipped for this.

I removed the pump and the impeller turns freely so no issue of gunge or seized bearing.
Does anyone have any suggestion as to which further readings can be made because I'm thinking of simply replacing the pump with a used one from e-bay?
Has anyone ever tried to open the pump? It looks like it was not made to be repaired.
Thanks
Peter
Hi Peter,

I suggest that you purchase a OBD dongle (I use OBDLinkMX+) and download the CarScanner App and it will report DTC Codes, it also allows you to clear some of them.
The code I was getting was "Code P0C73 Water pump error”.
I haven't done any more work on the old pump, apart from scrape away all the protective gunk, I purchased a new one via Ebay Japan and that solved my issue.
I’ve included some photos of test volts on the plug and the OBD dongle etc.
Sounds like a new pump may be required.

Good Luck
Bruce
 

Attachments

  • Coolant Pump Plug.JPG
    Coolant Pump Plug.JPG
    76.4 KB
  • Coolant Pump Relay.JPG
    Coolant Pump Relay.JPG
    99.6 KB
  • Coolant Refilling-01.jpg
    Coolant Refilling-01.jpg
    97 KB
  • DTC_P0C73.jpg
    DTC_P0C73.jpg
    19.7 KB
  • HBT06E02AC00ENG_Coolant Pump Circuit.jpg
    HBT06E02AC00ENG_Coolant Pump Circuit.jpg
    58.4 KB
  • OBDLinkMX+.JPG
    OBDLinkMX+.JPG
    82.2 KB
Hi Peter,

I suggest that you purchase a OBD dongle (I use OBDLinkMX+) and download the CarScanner App and it will report DTC Codes, it also allows you to clear some of them.
The code I was getting was "Code P0C73 Water pump error”.
I haven't done any more work on the old pump, apart from scrape away all the protective gunk, I purchased a new one via Ebay Japan and that solved my issue.
I’ve included some photos of test volts on the plug and the OBD dongle etc.
Sounds like a new pump may be required.

Good Luck
Bruce
Hi Bruce,

Thanks a hell of a lot for your effort in answering in such detail. I just ordered a second hand pump from a company not too far from here (I live in south western France) for 60€. They take in wrecks etc. and tested the pump after removal from, in this case, a total loss vehicle which had done 50000km.
Following recommendation from a local Peugeot mechanic (I have Peugeot Ion, Mitsubishi is virtually unknown here) I hooked the pump up to a 12V battery; between earth (black) and brown and also earth and blue; no result. I also did some resistance measurements but, due to lack of experience in electrical engineering, could make little sense of it.
I did some further measurements on the plug (male side) which feeds the pump. Everything corresponds to what you detailed in the picture except for the frequency measurement on the blue line which I couldn't make because I have still to learn how to use the voltmeter-oscillocope and the green line reading, and this does worry me somewhat. I get 0V for all positions of the key (ON and READY). It is not really clear what you mean by "data out" for the blue line and "pump control" from ECU. It depends on where your looking from, the pump or the ECU side. Although I am "only" a mechanical engineer my reading of the green line seems plausible if the green line is considered as the return signal from the pump to the ECU to verify that the pump is actually running. I think it was KIEV who said that he thought that Hall sensors could be glued to the rotor to signal to the ECU that the pump is running, and triggers the fault code if it is not. The fact that you obtain 14V on all lines in READY mode would IMHO mean that the pump is always in on status, which is a problem I have read about in other threads. I should have the pump by next Wednesday and will soon know the verdict. I have had two VW Caravelles, one of which is a good old 5 cylinder diesel which has done 372000kms. I do almost all the maintenance myself and am just hoping that my first experience with an EV will not be a nightmare.
Sorry for any language errors, I don't speak or write English very often any more. Fortunately I can also benefit from the french fora.
Wishing you all the best from a hot southern France
Peter
 
Hi Peter,

I suggest that you purchase a OBD dongle (I use OBDLinkMX+) and download the CarScanner App and it will report DTC Codes, it also allows you to clear some of them.
The code I was getting was "Code P0C73 Water pump error”.
I haven't done any more work on the old pump, apart from scrape away all the protective gunk, I purchased a new one via Ebay Japan and that solved my issue.
I’ve included some photos of test volts on the plug and the OBD dongle etc.
Sounds like a new pump may be required.

Good Luck
Bruce
The dongle and apps will be for later.
 
Bonjour Peter,

Your English is far better than my French …. ha ,,,

“Data Out” is just my terminology for the feedback pulse (Pin 2 WPN) from the pump to the EV-ECU so the ECU can monitor that the pump is working (210-230Hz), if it doesn’t receive this signal then it triggers a P0C73 error code.

The pump does have a permanent 12v or 14v Battery supplied to it between Pins 3 and 4 (depending whether the “ignition” key is ON or OFF) , and is then controlled (switched on/off) by the ECU via WP Pin 1 .

I feel that your new pump will solve your problem, follow the instructions for refilling the coolant liquid and you should be on your way again.

I have been a Francophile all my motoring life, having owned 3 Citroën ID19, ID21 and ID23 wagon in my younger days, great cars lots of good memories, then a Renault R4 fun car, and a Renault R16, and currently own a Renault Koleos (Nissan X Trail running gear) .

Living here in Brisbane summers are quite hot and therefore when charging the iMiev OBC gets very warm, I only do at home charging (240v) and only use either 6amp or 8amp charge rate. I am in process of installing a small extraction fan mounted near the OBC to exhaust excessive heat build up, hope it works, I have a Thermometer mounted on top of OBC to monitor temperature, will submit some test results in future (winter here at moment chilly 18c here today).

PS
I have read somewhere that you shouldn't run pump dry. Stuffs the impeller !

Kind Regards Bruce
 

Attachments

  • Controller Modules.JPG
    Controller Modules.JPG
    86.7 KB
  • Coolant Pump-01.jpg
    Coolant Pump-01.jpg
    27.7 KB
  • OBC-Fan Mod Cooler.jpg
    OBC-Fan Mod Cooler.jpg
    66.1 KB
Bonjour Bruce,

Indeed, you appear to be a believer in french cars. Funnily enough french cars, outside of france of course don't have a fantastic reputation. In France Peugeot is considered the most reliable. Personally I go for German reliability and solidity.

I received the water pump yesterday and with a huge amount of apprehension fitted it this morning. What a pleasant surprise to see that it works fine and the car is up and running again. I am considering buying the pump which feeds the cooling circuit of the battery pack, just for safety. I don't think running a pump dry would harm the impeller but there is a risk of damaging any seals between the PCB side (dry side) and wet side.

My next step might be to buy the OBDLink but it is rather expensive, even on Amazon. MickeyS70 suggested another model I think and he mentioned ELM327. I still need to read up on this because I don't even know if ELM327 is a communications protocol or an actual dongle. Perhaps you could help me further here.

Keep well "down under"
From a very hot southern France
Peter
 
ELM 327 is a chipset used by some OBDII dongles for negotiation of the Hayes AT Modem commands used to communicate with the vehicle. The OBDLink uses an STM chipset which is a better solution. There are lots of counterfeits out there and elm devices which don't work, so beware.
 
I am considering buying the pump which feeds the cooling circuit of the battery pack, just for safety.
The battery pack is purely air cooled
MickeyS70 suggested another model I think and he mentioned ELM327.
Just to clarify, as far as I know HobDrive (Android, paid version) is the only app that works with a triplet even using the cheap ELM Bluetooth dongle clones. I consider this combination a “budget” solution.

My personal preference is still the OBDLink LX, although it has become expensive, it communicates reliably with all apps/cars I have tried so far.
 
Hi Peter,
In total agreeance with Mickey and kiev.
I originally bought a iCarsoft i620, worked OK with the OBDZero App and caniON App, however would'nt work with the Car Scanner App or Hob Drive (it wouldn't allow DTC error resets) so I bit the bullet and bought the OBDLink MX + which functions great (it is expensive however it works).

And as Mickey says the Main Battery Pack is air cooled (fan on top of battery pack or Aircon when doing a fast charge), only the OBC, the Motor Controller and the Motor are liquid cooled.

happy days
Bruce

good that your "new" pump worked .....
 

Attachments

  • Cooling System_23.jpg
    Cooling System_23.jpg
    37.2 KB
  • Cooling System_24.jpg
    Cooling System_24.jpg
    50.1 KB
  • Cooling System_25.jpg
    Cooling System_25.jpg
    23.8 KB
Back
Top