hobdrive - and i-MIEV ion zero, show electronic control units, reset errors

[zsandor]

Try to select ECU Type in the settings:
-Mitsubishi SRS only DTC KWP
or
-Mitsubishi SRS only DTC CAN

Hi, i downloaded the newest beta version, but do not have this options. I have following ECU types for Mitsubishi:

Mitsubishi 4M41 (Pajero)
Mitsubishi CVT+OBD2 CAN
Mitsubishi iMiEV Li-ION
Mitsubishi iMiEV Li-Titanate
Mitsubishi ?imicab iMiEV LI-ION 2014
Mitsubishi MUT
Mitsubishi Outlander PHEV+OBD

where to get that additional ECU types?

Screen/settings/version and update/version?

Screen/settings/vehicle settings/ecu settings/ECU Manufacturer (filter) - Mitsubishi
Screen/settings/vehicle settings/ecu settings/Vehicle Type ECU - Mitsubishi SRS only DTC KWP or Mitsubishi SRS only DTC CAN

PS. Reading errors will only work in the full version

I have the 1.5.48 full/licensed version. It does not install any newer (applyed for 1.6.6 beta version), even if i delete end reinstall the app...
Will try it with another device

[kdika]

- v1.6.4 04/01/2020
- ECU:
Mitsubishi SRS only DTC CAN
Mitsubishi SRS only DTC KWP

android > 4.4

Last beta - v1.6.13 12/18/2020

[zsandor]

Many thanks!!!! ))))) i installed on another android device a never version of Hobdrive and i got than the two above mentioned ECU’s. The second one has worked and could reset the airbag warning light on my C-Zero as this was caused by disconnected switch under the driver seat, and had no real failure in the system, the light was not reocurring. Will also check the cell balancing function soon
Thanks!

[vh2q]

Can someone remind me how to get to the traction battery diagnostics? Ie which screens to navigate? Call me dumb but i hsve done this in the past, cannot remember exactly how, i cant find those screens now even though the rest of it seems to work.

[kdika]

Full version read DTC: screens/Diagnostic

[stoatwblr]

Is it possible to add a trigger for the battery calibration routine?

My car reports 29Ah capacity but is only accepting 26Ah charge. I know it will _eventually_ adjust downwards (1Ah per 1000km) but knowing it's already way out means I would prefer to have it reset to what it is now

This can be done with MUT3, but dealers want $$ for the privilege and it means not having the car for a couple of days, when it could simply be done over a charging cycle

[stoatwblr]

How can i start the balancing function?

You can only do this when charging (not Chaedamo).

If you don't do it inside Hobdrive, it's triggered automatically by the charging routines once the car hits about 95-98% full and is why it takes so long to get from 95 to 100% charge (you can watch the balancing function switching on/off)

[Serhge]

it's been a long time since I've run here, balancing during charging can't charge the cells correctly, the balancer is only 40 mA, so you need to balance after charging at the remaining 90%, you need to turn it on yourself, there won't be a good result in any other way, it also takes several days in a row to balance, consider yourself that a balancer of 40mamp can, right, almost nothing can, it takes a lot of time, but even though it's long, but the result will be good! tested personally !

[Serhge]

Is it possible to add a trigger for the battery calibration routine?

My car reports 29Ah capacity but is only accepting 26Ah charge. I know it will _eventually_ adjust downwards (1Ah per 1000km) but knowing it's already way out means I would prefer to have it reset to what it is now

This can be done with MUT3, but dealers want $$ for the privilege and it means not having the car for a couple of days, when it could simply be done over a charging cycle

I didn't understand, do you want to reset the data?
or to have the battery recalculate its capacity?
I tried to make them recalculate the capacity , but I didn't really understand how to enter this mode , I need to activate this function, but I didn't understand in what state of charge. you can add it , it's not a problem, you need a little time and then check on an electric car , everything seems to be simple , but it's not as it seems at first glance , although everything is possible if you are smart.
and also, since we have a good person and at the same time is the developer of this software, I think it's real.

taking into account the fact that for today I think this is the most adequate application with good functionality for our cars)

[Imievnewb]

I have a Bluetooth veepeek obd2. I was able to reset engine code with Hobdrive using android device. I was have difficulty getting it to recognize obd2 with IOS.

OBDzero worked great with it. Didn’t see an option for engine codes or to reset them. You do see all the voltages of each battery etc though.

Car scanner I was able to read engine code but it wasn’t able to reset it. I got an error message something about not compatible and only basic functionality was available.

Hope this helps!