Recent content by smueller99au

Hi Mikkel. Those spliced wires were inside the OBC within the black conduit between the connector and the DC board. I still have the old wiring if you need to take a look. Let me know if you need to borrow an OBDII cable and the Peugeot Diagbox software. It gives us everything we need for the...

Great! That’s what the forums are for. The most useful information to start with is that the orange cables can remain disconnected without affecting the running of the car. This is not possible in many other electrical cars, like the Renault’s for example.

The red sealant is gasket goo, which was just my choice of sealant because that is what I had. Hopefully it does the job long term. But yeah, when I cracked the bottom lid I could see some non original sealant there. If it wasn’t sealed then I would have found the coolant before the electronics...

Righto. I have finally solved the issue, and found what the original problem was (high confidence level). First off a big THANKS to those that helped out, especially KIEV. It really helps when someone can respond with some useful information that isn't apparent at first. Recap: The first...

Sorry for the delay in posting... I've been busy fixing my DC/DC charger. Solved now. I use a VMWare Windows XP Pro installation with Diagbox 7.57. It works just fine will all 3 cars. Note that the Ion and Citroen have the PSAradio together with the PSA SOS box in Europe. Whenever I run Diagbox...

I can confirm that the Peugeot Diagbox software and adapter works just fine with all 3 cars - iMiev, Ion and C-zero. I have used it successfully on all three (I currently have an Ion and iMiev, but have used it on a friends C-zero without problems). Regarding the RPO number, just enter 00000...

Thanks for your response Kiev. I checked the one fuse I could see on the DC/DC board before installation. I also checked the connectors and resealed the covers. I hope nothing has come loose, but I had better remove the module again and check. Battery is brand new. I have mentioned this...

OK, it seems I jumped the gun here. DC/DC charger worked fine for two weeks. But it has stopped again now. Odd. Diagbox reads P0A09 Converter fault from the EV ECU. But it's interesting that there is an older fault P1A44 (leak sensor - earth fault) 20km previous. So, what happened? The first...

Further update. Problem is fixed. I went through all the connectors, earth wires, etc. as per the service manual and nothing seemed wrong. Did the diagnostics tests also as per the service manual but it passed everything. So, nothing more to do except replace the entire OBC. Well, this sorted...

A little update for you. Battery is new - Exide Premium EA386 (UK:054TE). I just can't find the date stamp on it. Found the right connector but haven't had a chance to pull it apart yet. I'll try that on the weekend. I drove it 6 times today. The first 2 times the charger worked as it should...

Thanks for the feedback. Hopefully I can sort out the existing module and not have to replace it.

Hi Don. Thanks for the reply. As I mentioned the battery is pretty new, as in within 6 months. I’ll go check if it has a date stamp on it to confirm though. What I’m worried about is that the charger drives 14.8V!! This is why it’s shutting down. I managed to get it to drive today at 14.6...

Hi all. I have searched for a while looking for an answer to this but haven't yet found any. Sorry if it's a duplicate post from somewhere... I have an old iMiev, 2011 build. It has the old charger, ZHTP1529R, the one with the little top hat filter on it. Can I replace that charger directly...

Hi all. I'd like to continue this post from Casper here. I've bought his car knowing that it had a problem. I have found a complete spare OBC module that I can use to replace the existing one, but I was also thinking to see if I could fix the problem before removing the existing module. A...

Hi all. I just wanted to add that I’ve had the same issue on my iMiev, and worked on another car with the same. Both had water in the electronics compartment. However, with mine I had to pull the top board away and get to the second layer where the water was also. Not sure which layer had the...