Page 3 of 3

Re: Better charging controls

Posted: Fri Jan 20, 2012 10:20 pm
by Wee John
No timers are necessary, the remote can be set to turn on the charger after a set delay and can also turn off the charger after a set amount of charging time, it looks like the car remembers the time the remote was set as you don't need to reset the times the following day. I tried to post pictures from the owners manual but they came out huge, not suitable for posting.

Re: Better charging controls

Posted: Sun Jan 22, 2012 12:52 am
by MtnViewMark
Indeed, I can confirm this, now that we've been using our Level 2 EVSE for about a week. The remote does remember the time of day for start (and optionally stop), even though the user interface is in terms of hours of delay.

For example: On Monday, you come home at 5:15pm, plug in, and set the start charge delay (with the remote) to 7 hours, then the car will start charging just after midnight. If, on Tuesday, you come home at 9:45pm, plug in, then turn on the remote and tap either of the adjustment buttons, it will show a delay time of 2.5 hours, just what you want to start just after midnight.

Note that in all cases, when you plug in the car, it starts charging immediately. Then you need to turn on the remote, select a delay time (even if it is just tapping the button to recall the setting), and then send the delay charging command to the car (another press on the remote.). Then, after about a minute, the car will stop charging, and wait for the set time to start again.

Since the car is actually the device doing the timing, my one wish is that there were a button right in the car (or perhaps in the charging well!) that let me select delayed charing right when I plug it in. Then I would have to fiddle with the goofy remote.

Re: Better charging controls

Posted: Sun May 20, 2012 3:01 am
by fjpod
In my garage, i have a commercial type Intrmatic timer that I used to use for my pool filter. I run my imiev oem chargr from that timer. As much as I have mastered the remote, I find my timeer is so much easier. I dont even set the time of day properly. Just pull the wheel to set the delay and adjust the off switch for the number of hours charging time I want. Walk away, I'm done.

Oh, BTW, the charging will start when the timer turns the juice on, even though the cord was plugged into the car first.

Re: Better charging controls

Posted: Thu Jul 19, 2012 12:51 pm
by JoeS
Reviving this old thread...

I've been using my Remote almost every day since I bought the car in February. I rarely use my Remote to delay starting a charge, and do use it at varied times during the day to terminate the charge at around 14 bars. It often takes a number of attempts, with the car giving me a Remote Error message before it finally "takes", both with entering zero into the ON time and then the ON->OFF time. Still haven't quite pinned down the Error cause despite trying various time delays before hitting the Remote top button, although doing it in the morning after having done it the previous night seems to make it hiccup more, and it seems to happen more often using the SPX instead of Mitsu's EVSE. No matter, yesterday I gave up on the Remote...
Update 9/2/12 Traced my Remote issues to compatibility with my SPX Xpress Level 2 EVSE. It takes a few tries before the programming takes hold without an error message. The Mitsubishi (Panasonic) Level 1 EVSE works every time with the Remote.

I've gone back to the old-fashioned spring-wound Intermatic FF46H 6-Hour Spring Loaded Wall Timer, which disconnects both poles, although it might be overstressed in this application despite the slow power ramp-up of our iMiEV charger and the capacitive input which should limit turn-off peak currents. Here are its specs:
Resistive: 20 Amp, 125 VAC, 50/60 Hz, 10 Amp, 250 VAC, 50/60 Hz, 10 Amp, 277 VAC, 50/60 Hz
Tungsten: 7 Amp, 125 VAC
Motor: 1 HP, 120 VAC, 50/60 Hz, 2 HP, 240 VAC, 50/60 Hz

Inasmuch as I needed to package this timer, I decided to make it transportable and put it together with an energy consumption meter that I picked up off eBay: 230V 100A LCD DIN-rail Type Kilowatt Hour kWh Single Phas... (170850363518). It is a very simple meter that merely accumulates and displays kWHr consumed and does not reset when power is removed. This one is evidently good for both 50Hz and 60Hz.

So far, they both seem to work and I now have a definitive way of measuring my energy consumption when I take my iMiEV and charge at friends' houses using their dryer outlet. For now, I've screwed it to the wall and I'm starting to record the kWHr readings and compare them to my T.E.D. readings.

Pictured below are the two gadgets mounted in a gray box from Home Depot, with the NEMA L6-30 output connector built into the top of the gray box and the input pigtail plugging into my L6-30 wall socket (which also contains NEMA L6-20 and 6-20 sockets).


Re: Better charging controls

Posted: Fri Jan 19, 2018 1:32 pm
by GdB
I started a new thread that seems somewhat relevant to this and a few other threads, so please excuse my promoting it.
Optimum EV Charging and Electricity Consumption Time for GHG, TOU