Go to advanced search

by Timh
Sun Dec 23, 2018 4:20 pm
Forum: General Technical Discussions
Topic: Has anyone removed Air Con unit
Replies: 0
Views: 827

Has anyone removed Air Con unit

Just wondering if anyone has re-used the Air Con compressor (or whole system) in another car? Does it only run at 330V? I am parting out a 2011 i-miev and wondered if I could re-use it, but I will probably be running at a lower voltage. Can't find much tech info on the compressor etc. Thanks for any...
by Timh
Sun Jul 29, 2018 7:41 pm
Forum: General Technical Discussions
Topic: Help with scanned error codes
Replies: 21
Views: 4242

Re: Help with scanned error codes

For anyone wondering, I managed to get to the "ready" stage after recharging the 12V battery. It seemed to reset the system and cleared the way for everything to work. I couldn't drive it, as it had a flat tire, and the oil had been drained from the trans. I did want to check the motor wou...
by Timh
Thu Jul 19, 2018 6:36 am
Forum: General Technical Discussions
Topic: Help with scanned error codes
Replies: 21
Views: 4242

Re: Help with scanned error codes

Yes I'm aware of that, I just happened to take that pic while i was moving through the gears to check the dash was showing the correct gear as per the shifter. I'm not getting the ready light, obviously there's still a few errors to be ironed out, just got to work out what they are. Perhaps its time...
by Timh
Wed Jul 18, 2018 10:59 pm
Forum: General Technical Discussions
Topic: Help with scanned error codes
Replies: 21
Views: 4242

Re: Help with scanned error codes

We repaired the sensor switch, and now it's back on and the correct gear is shown on the dash when moving through the gears. Unfortunately I still can't get it to run as some other error is preventing operation. There is a constant alert sound that starts a little while after turning the ignition an...
by Timh
Sat Jul 07, 2018 6:12 am
Forum: General Technical Discussions
Topic: Help with scanned error codes
Replies: 21
Views: 4242

Re: Help with scanned error codes

Thanks for that Kiev, I will look into those links and think about whether it is worthwhile pursuing.
by Timh
Sat Jul 07, 2018 4:18 am
Forum: General Technical Discussions
Topic: Help with scanned error codes
Replies: 21
Views: 4242

Re: Help with scanned error codes

Well I removed the shift position switch, and it appears to be pretty damaged. See below pics before and after dismantling. I assume this part will be either expensive or impossible to replace without ordering from Japan, so I might just start stripping the car without knowing if the motor etc will ...
by Timh
Thu Jun 28, 2018 6:50 pm
Forum: General Technical Discussions
Topic: Help with scanned error codes
Replies: 21
Views: 4242

Re: Help with scanned error codes

You're keen eyes are right.
Shows up clearly with the flash.
Image
by Timh
Wed Jun 27, 2018 10:54 pm
Forum: General Technical Discussions
Topic: Help with scanned error codes
Replies: 21
Views: 4242

Re: Help with scanned error codes

No the gear indicator isn't showing on the dash at all. We will try and play around with the wiring and connections on the weekend.
by Timh
Tue Jun 26, 2018 6:17 pm
Forum: General Technical Discussions
Topic: Help with scanned error codes
Replies: 21
Views: 4242

Re: Help with scanned error codes

If you mean the black connection to the gearbox as shown in the below picture, then no we didn't touch that. Is that the shift sensor you're talking about?

The grease is just from when the CV joint was busted open.

Image
by Timh
Tue Jun 26, 2018 2:55 pm
Forum: General Technical Discussions
Topic: Help with scanned error codes
Replies: 21
Views: 4242

Re: Help with scanned error codes

This is after we took the wheel off and reinserted the drive shaft into the CV joint and the motor.

Image

Go to advanced search